When you're shopping for a stroker kit, the first question you should ask yourself is how you intend to use the engine. Most driver Mustangs, even with occasional weekend drag racing, can get by with a cast-iron, cast-steel, or nodular iron crankshaft; forged steel I-beam connecting rods; and hypereutectic pistons with ductile iron rings. You really won't need any more than that though most kits already have forged pistons. Weekend drag racers can benefit from forged pistons instead of cast or hypereutectic.
Cast-iron, cast-steel, and nodular iron crankshafts are all basically the same idea-a flexible, durable iron shaft for street and occasional weekend drag racing. Unless you intend to go racing full-time or run nitrous, supercharging, or turbocharging, an iron shaft will live a long time in your engine. When taking an engine to extremes with full-time racing, nitrous, or supercharging, forged pistons become mandatory for durability or you risk breaking a forged steel crank and H-beam rods.
Not only is crankshaft material an important consideration, but so is design. Look closely at journals and how they're machined. You want journals with good load distribution across the face and fillet radii. It's also a good idea to look at oil galleys and journal chamfering while you're shopping. These are points you will need to discuss with a tech rep when ordering your stroker kit.
Another important consideration is stroker crankshaft fitment in your 302, 351, 390, or 460 engine because rotating and reciprocating internals must clear the block and other important components like camshaft and oil pump.
Another less important issue for street cars is crankshaft weight and aerodynamics. For a street Mustang, you're not going to be that concerned with crankshaft weight or aerodynamics. However, weekend and full-time drag racing is another story. You're going to want the least amount of crankshaft weight possible along with counterweights that are knife-edged to slice through air with the greatest of ease. Crankshaft weight and aerodynamics, not to mention dynamic balance, affect how quickly an engine accelerates.
Your Mustang was factory fitted with forged steel connecting rods, which work quite well shotpeened and upgraded with ARP bolts when building a stocker. When you make the decision to build a stroker, you're starting out with a clean sheet of paper. Street and occasional weekend racer engines need only I-beam forged steel connecting rods, which are more durable than stock rods. What makes an aftermarket I-beam rod stronger is the material it comes from. Eagle, for example, makes its most basic I-beam rods from SAE 5140 forged steel and fits them with ARP 8740 3?8-inch bolts for unequalled strength. Eagle I-beam rods are fitted with alignment sleeves for optimum cap and rod fit. Machining is done with CNC technology, which keeps your detail work to a minimum, although we suggest checking everything during a mock-up.
Forged H-beam connecting rods are race-only technology and expense. They aren't pieces you'd run with a cast-steel crankshaft, but instead a 4340 steel or steel billet crank. H-beam rods are forged from SAE 4340 steel and are designed for all-out racing activity. This makes the H-beam rod unnecessary for your daily driver and weekend cruiser. Eagle's 4340 H-beam rods sport 3?8-inch ARP 2000 bolts (small-block) and alignment sleeves for rock-solid durability. What takes Eagle H-beams over the top is perfect sizing on the Sunnen Krossgrinding machine. These guys can take up to 900 horsepower if you're so inclined.
There are three basic types of pistons available in the marketplace-cast, hypereutectic, and forged. Cast pistons are original to most vintage Ford engines because they're cheap, quiet, and offer good expansion properties. Hypereutectic pistons are cast with high silicon content for strength without the cost of forging. They offer similar expansion characteristics as cast with added strength. You can build a daily driver and weekend drag racer using hypereutectic pistons and save a few bucks.
Forged pistons offer high strength for high-performance applications, yet undesirable expansion properties because they expand more than the cast variety. This means looser tolerances cold, which makes forged pistons noisier on cold start up. Sometimes, forged pistons never get quiet with heat. Just ask anyone with a 4.6L SOHC or DOHC Modular V-8 about piston rattle during cold start-up and they will explain the disadvantages of forged pistons.
When you're amassing a stroker package, most of the brainwork has been done for you, including piston selection, with Eagle and with Coast High Performance. Where it gets tricky is compression ratio, rod length, and crankshaft counterweight sizing. Eagle's Alan Davis tells us the biggest hurdle of building a stroker is understanding the piston, rod, crank combination and how it works together. "Imagine a single cylinder's worth of crank, rod, and piston all assembled at bottom dead center," Alan tells us. "If you increase stroke, it will pull the piston down into the counterweight. Not good. That's why we increase rod length in stroker kits. But if you rotate the crank, everything sticks out of the top of the block, which is why we change wristpin location to get the piston flush with the deck."
Alan adds that wristpin location is known as compression height, yet he tells us that he doesn't agree with that terminology. "Wristpin location isn't the only thing that affects compression height. While changing the compression height by itself would alter the compression, it is not the 'ideal' way to change the compression if that is what you want to do. The location of the pin in the piston is really dictated by the stroke and rod combination you are attempting to build instead of the compression ratio." Alan says he'd prefer to call this dimension pin height rather than compression height.
With all this in mind, how do you cram all this hardware into a 302 block? "This is where block deck height comes into play," Alan says. "Ford's 302 has an 8.206-inch deck height, which is the distance between main centers and block deck. The 351W has a 9.500-inch deck height. You've heard some folks talk about zero deck engines, where pistons come to the top with no clearance whatsoever, flush with the deck."
According to Alan, there's roughly 0.020-inch of deck clearance with most factory engines. This is why you should do a mock-up before final assembly. A raw mock-up without piston rings, but with bearings, allows you to check all dimensions and make any needed changes. If there's too much clearance at the deck, you have too much deck height. If the piston sticks out of the hole, you have no deck height. In either case, you may have to make a piston change to get it right. Situations like this are decidedly rare.
When adding stroke to an existing block, we make significant changes to the engine's physics. Compression ratio is cylinder and chamber volume with the piston at bottom dead center versus cylinder and chamber volume with piston at top dead center. In other words, with 10.0:1 compression, you have 10 parts volume (bottom dead center) to one part volume (top dead center). This is a dynamic you must be aware of in the planning stages, then confirm physically during mock-up. This dynamic is known as swept volume.
When compression is too high, you can opt for a dished piston or a deeper dish to lower it. The problem there is that a dish piston gets closer to the wristpin. You can also opt for a cylinder head with larger chambers. Those are two solutions, and there are more.
Another element to consider with stroker kits is rod ratio, which we mentioned earlier. Rod ratio is rod length divided by stroke. In other words, rod length versus stroke. Rod ratio is important to power. It's also important to fit and function. You don't want a connecting rod that's too long.
"Rod ratio has several effects," Alan comments. "The most important one as it relates to strokers is side loading." When rod ratio increases, side loading decreases. By the same token, when it decreases, side loading increases. Side loading is the side load placed on the piston as the crank throw comes around and drives the piston skyward, yet right into the cylinder wall. When side load increases, so does piston and cylinder wall wear, friction, and heat.
Alan suggests a maximum rod ratio of 1.70:1 on 302- and 351ci Fords and 1.72:1 on the big-blocks. The generally accepted range is 1.50:1 to 1.70:1. A longer rod yields more dwell time at each end of the cylinder bore, which means more time for air and fuel to amass. That gives us better throttle response thanks to longer dwell time. However, there's also a price to be paid when connecting rods become too long in terms of excessive wear and borderline geometry.
Ford's 428, on the other hand, has a smaller bore but a longer stroke than the 390 and 427, making it a real powerhouse down low for good traffic light-to-traffic light power.
Quick Engine Math
How do you determine an engine's displacement? All you need to know is bore and stroke, then follow this simple formula.
Engine Displacement = bore x bore x stroke x 6.2838
Let's take a typical 302 that has been bored .030-inch oversize with a 4.030-inch bore. You can calculate the new displacement by multiplying the 4.030-inch bore times itself (4.030 inches) times a 3.000-inch stroke times 6.2838 to arrive at 306.1637 cubic-inches. Taking the 302's 3.000-inch stroke and increasing it to 3.400 inches yields 346.985 cubic-inches rounded off to 347ci. Increase bore size another 0.010-inch and you get 348.709 cubic-inches or 349ci. Boring a 302 block beyond 4.040-inches is not recommended, though some go to 4.060-inches, which is cutting cylinder wall thickness way too close. Going beyond 349ci in a 302 block isn't recommended.
Forged pistons offer high strength for high-performance applications, yet undesirable expansion properties because they expand more than the cast variety.
Here’s an example of stroke. Stroke is full piston travel from bottom dead center to top d
These are elements important to building a stroker because everything you know about your
This is the 347ci Street Fighter kit from Coast High Performance, which includes a cast-st
Here’s the more upscale 347ci Dominator engine kit from Coast High Performance for just ov
Eagle can help you with just about any engine project because it offers such a broad selec
For an engine build to work effectively, everything has to fit and function smoothly, whic
Here’s where a stroker kit can bite you if you haven’t done some advanced planning, mock-u
When you add things like block stiffening girdles, windage trays, and baffled oil pans, ne
This example of an MCE Engines mock-up demonstrates the close attention to detail. This co
When you’re calculating compression ratio, include everything between the piston and chamb
Despite concerns over durability, you can make a lot of power with a cast-steel crank and
When adding displacement via stroke, cam profile and valve timing events have to change ac