If you've been following our "Plan for Ponies" series since it first appeared in the Oct. 2000 issue, then you understand that usable real-world power does not come easy. West Coast Classic Mustang's Jerry Choate provided us with his father-in-law's dead stock '65 Mustang GT hardtop as a test mule for our effort. We drove it across Southern California's San Fernando Valley to Mike Morgan Motorsports in Burbank for a quick analysis of how much power an aging stock Mustang could produce. Derek Real of Mike Morgan Motorsports pulled the Mustang onto the chassis dyno on a hot day last June for that first pass in stone stock condition right off the street-untouched: horsepower was 128.4 at 4,100 rpm and torque peaked at 193.9 lb-ft at 3,400 rpm.
We popped the hood for a closer look. For starters, the vacuum advance wasn't working-thereby causing a lapse in power. Stock ignition points and condenser were marginal at best. We installed a Pertronix Ignitor, which netted 2.7 hp and 1.1 lb-ft of torque. This told us that the Ignitor is more about reliability and smooth performance than power. Idle quality improved with the Ignitor as well.
After we installed the Ignitor, we removed the air cleaner for a modest increase in horsepower and a slight loss of torque. Fresh spark plugs made very little difference in performance.
When West Coast Classic Mustang installed the Edelbrock Performer RPM intake manifold and carburetor in Part Two ("How To Plan For Ponies: Part Two in a Five-Part Series," Nov. 2000, p. 42), we expected an obvious increase in power-but that's not what we received. We actually lost torque and noted a modest increase in horsepower. Derek Real super-tuned our 289 for modest gains in horsepower and torque. We gained a total of 16.3 hp and 7.4 lb-ft of torque with super-tuning and an induction swap; however, adjustments in spark timing and changes in carb jetting didn't do much for performance. Not bad, but nothing to go bench racing with either.
When we installed Hedman headers and the Turbo 211/44-inch exhaust system from National Parts Depot in Part Three ("How To Plan for Ponies: Part Three in a Five-Part Series," Dec. 2000, p. 38), we witnessed increases in power-especially with more super-tuning from Mike Morgan Motorsports. With a fresh exhaust system and carburetor tuning, power jumped to 224.7 lb-ft and 158.5 hp at the rear wheels. Just for fun, we uncapped the headers and let the Mustang scream with a loss in torque yet an increase in horsepower. The exhaust-system back pressure gives us torque, especially when valve overlap is optimum. So uncapping the headers isn't always going to help you at the dragstrip. In fact, it can hurt you out of the hole.
This leads us to the entire point of our power lecture. In order to generate real power, you have to modify your engine as a package-not piecemeal. Tuning and a better ignition system netted modest increases in power. An Edelbrock intake and carb bumped the power considerably. But our 289 didn't really wake up until we rounded out the package with Edelbrock Performer RPM cylinder heads. Performer RPM aluminum cylinder heads sport larger-than-stock valves and ports. What's more, the port design is cleaner. Aluminum heads help eliminate combustion heat, enabling us to advance spark timing without the risk of detonation and engine damage.
West Coast Classic Mustang removed the stock 289 4V heads and installed the Edelbrock pieces fitted with Comp Cams' roller rockers and pushrods. Here's how Part Four played out.
Installing a Pertronix Ignitor...
Installing a Pertronix Ignitor retrofit improved reliability and idle quality. It also gave us a nice 2.7hp gain.
Removing the air cleaner to...
Removing the air cleaner to gain power is a legitimate myth.
We gained 4.1 hp, but we lost...
We gained 4.1 hp, but we lost torque. Despite the modest gain in power, we prefer to run the engine with its air cleaner installed.